Search Results (54,581)

Non-destructive ultrasonic testing can be used to assess the properties and condition of real machine elements during their operation, with limited (one-sided) access to these elements. A methodological question then arises concerning the influence of the material properties of such elements and the condition of their surfaces on the result of ultrasonic testing. This paper attempts to estimate the influence of material hardness and surface roughness on the result of such testing study area testing machine or plant components of unknown exact thickness. Ultrasonic testing was carried out on specially prepared steel samples. These samples had varying surface roughness (Ra from 0.34 to 250.73 µm) of the reflection surface of the longitudinal ultrasonic wave (the so-called reflectors) and hardness (32 and 57 HRC). The ultrasonic measures were the attenuation of the wave, estimated by the decibel drop in the gain of its pulses, and the propagation velocity of the longitudinal ultrasonic wave. Ultrasonic transducers (probes) of varying frequencies (from 2 to 20 MHz), excited by a laboratory and industrial defectoscope were used as the source of such a wave. The results of our research provide a basis for the recommendation of two considered ultrasonic quantities for assessing the material properties of the tested element. This is of particular importance when testing machines or plant components of unknown exact thickness and unknown roughness of inaccessible surfaces, which are the reflectors of the longitudinal ultrasonic wave used for testing. It has been demonstrated that by using the ultrasonic echo technique, it is possible to evaluate the roughness and hardness of the tested elements. Full article

A tumbler screen-type residual film–impurity mixture wind separator is the key equipment for the secondary utilization of farmland residual film. During its operation, the proportion of impurities in the separated waste mulch film intermittently increases, resulting in poor working stability of the device, which may hamper long-term operation. To address the above issues, the material inside the separation unit was continuously monitored, and the main factor affecting separator performance was determined to be the challenges in the effective depolymerization of some residual film-impurity mixtures. The principles of agglomeration and depolymerization of the residual film-impurity mixtures were analyzed using computational fluid dynamics (CFD) and discrete element method (DEM) flow-solid coupling simulation methods. The key factor affecting the disaggregation of the mixture was the collision force between the residual film–impurity mixture and the trommel screen. The collision force was maximum when the residual film–impurity mixture first collided with the trommel screen when it was fed into the separation device. Furthermore, simulations were carried out for different inlet structure forms; the evaluation index was the maximum collision force of the residual film–impurity mixture agglomerate on the trommel screen. The best disaggregation effect was obtained with a square feed inlet and at a feeding rate of 202 kg/h. A prototype was built using these specifications for verification. The average value of the ratio of impurities in the residual film was 6.966%, the coefficient of variation was 7.38%, and the dispersion of statistical results was small. The ratio of impurities in the residual film was kept constant during the continuous operation of the wind separator. Thus, in this study, we analyzed the agglomerate disaggregation process and provided theoretical insights for determining the optimal structures of the inlets of various cleaning devices and the feeding volumes. Full article

The use of electrically conductive mortar (ECM) is a relatively new construction material technology developed to obtain high conductivity and mechanical strength. This study presents an experimental investigation on the heating performance and flexural strength properties of ECM mixed with carbon fiber (CF) and steel fiber (SF), which are conductive fibers. Furthermore, the internal microstructure of the ECM was analyzed with a scanning electron microscope (SEM) and thermogravimetric analysis was carried out using a thermogravimetric analyzer (TGA) device. The results of the experiment showed that the incorporation of SF had little effect on heating performance. In the case of CF, however, it was found that as the fiber contents and applied voltages increased, the heating performance increased. In particular, the maximum heating temperature of the ECM-CF125 specimen was 145.1 °C at an applied voltage of 30 V and an electrode spacing of 40 mm, which was about 7.3 times higher than the initial temperature (20 °C). In addition, the flexural strength of ECM mixed with SF was higher than that of plain mortar (PM), whereas the ECM-CF125 specimen showed a greater tendency to significantly decrease. It was confirmed that the hydration products and internal microstructures of the specimens were unaffected by repetitive electrical heating, and the ECM maintained stable electrical conductivity. Full article

China is rich in coal resources under water bodies. However, the safety prediction of high-intensity mining under water bodies has long been one of the problems encountered by the coal industry. It is of great significance to realize safe mining under water bodies, improve the recovery rate of coal resources and protect reservoir resources. Therefore, this article takes the No. 5 coal seam and No. 11 mining area of the Wangwa Coal Mine as the research object, and integrates physical simulation, numerical simulation, theoretical analysis, and other methods to study the development height of water-conducting fracture zones in fully mechanized top coal caving mining. Solid–liquid coupling physical simulation tests reveal the failure characteristics of overlying strata in goaf and the seepage law of reservoir water under the influence of mining. By comparing the monitoring data of borehole leakage, the measured data obtained by borehole monitoring with the height data of the water-conducting fracture zone obtained by the traditional empirical formula of three-under standard, the error between the two is as high as −29.39%. In this case, the variance correction coefficient is used to correct the empirical formula, and on this basis, in order to effectively protect the surface water dam and water body, the mining height of the coal seam in the working face with limited height mining is inversely derived. The research results provide a basis for the safety prediction of high-intensity mining under the reservoir dam in the ecologically fragile areas of western China and a scientific guarantee for the formulation of safety measures under such conditions. Full article

With the rapid advancement of autonomous vehicles, a transformative transportation paradigm is emerging in the automotive industry, necessitating a re-evaluation of how users engage with and utilize these evolving settings. This research paper introduces an innovative interaction system tailored for shared autonomous vehicles, focusing on its development and comprehensive evaluation. The proposed system uses the car’s windshield as an interactive display surface, enabling infotainment and real-time information about the surrounding environment. The integration of two gesture-based interfaces forms a central component of the system. Through a study involving twenty subjects, we analyzed and compared the user experience facilitated by these interfaces. The study outcomes demonstrated that the subjects exhibited similar behaviors and responses across both interfaces, thus validating the potential of these interaction systems for future autonomous vehicles. These findings collectively emphasize the transformative nature of the proposed system and its ability to enhance user engagement and interaction within the context of autonomous transportation. Full article

Jujutsu is a close-contact grappling combat sport. Karate is a long-distance combat sport, primarily using strikes and kicks. Well-designed strength characteristics should be capable of differentiating between participants of martial arts and combat sports, especially if, due to training preferences, they develop particular preferences for grappling or striking that differentiate them, as is the case in jujutsu and karate. One hundred and seventy-eight participants were tested for their age, weight, years of training, style (modern jujutsu, Polish and German groups, karate Kyokushin, karate Shotokan), skill level (Kyu or Dan grade), gender, and handgrip strength (HGS). An analysis of variance utilizing age, weight, years of training, martial art, gender, and skill in explaining HGS showed that variance in skill level and the interaction between skills and weight were significant. Furthermore, a post-hoc Tukey’s HSD test based on skills separated practitioners with the second Kyu from those with the sixth Dan grade. There were two groups identified when a similar analysis was conducted for the interaction between skill and weight. The first one encompassed all athletes below the fifth grade, whereas the second one comprised the remaining practitioners. Principal component analysis with gender as a grouping variable showed that women formed a partly separated group of athletes, with the most differentiating factors being age and years of training. When the grouping variable was skill level, the most influential variables were weight, HGS, and age. Finally, utilizing martial arts as a grouping variable showed that age, years of training, and skill were the essential variables. Our study has demonstrated that by utilizing HGS in combination with such characteristics as weight, age, years of training, gender, Dan grade, and martial arts, it is possible to identify differences between people training distinct martial styles, those with varying skills, and those representing opposite sexes. However, the differentiation is only sometimes apparent. Full article

Smart surfaces with controllable friction have generated considerable attention lately. However, most composites prepared with traditional fillers cannot achieve “real-time” friction conversion. Herein, a new smart surface was designed to achieve different friction coefficients (0.65 and 0.12). Different coefficients of friction were reversibly and precisely controlled via heating. Via friction and heating, 1H,1H,2H,2H-perfluorohexyl hexadecane (PHHD), a kind of phase-change material—paraffin wax—was released from the microcapsules, and a stable and complete film was formed. It changed the interface from “solid-solid” to “solid-liquid” in a dry friction state. The composite contains microcapsules that prevent phase separation between PHHD and matrix, which enables the composite to have a long service time and switchable friction performance. In addition, this composite can maintain its extraordinary ability even in harsh environments like UV irradiation. By demonstrating switchable friction based on changes in the interactions between contact interfaces, this work provides a new principle for designing smart tribological composites. Full article

In order to find optimized headlight distributions based on real traffic data, a three-step approach has been chosen. The complete investigations are too extensive to fit into a single paper; this paper is the last of a three part series. Over the three papers, a novel way to optimize automotive headlight distributions based on real-life traffic and eye tracking data is presented. Across all three papers, a total of 119 test subjects participated in the studies with over 15,000 km of driving, including recordings of gaze behaviour, light data, detection distances, and other objects in traffic. In this third paper, driver gaze behaviour is recorded while driving a 128 km round course, covering urban roads, country roads, and motorways. This gaze behaviour is then analysed and compared to prior work covering driver gaze behaviour. Comparing the gaze distributions with roadway object distributions from part two of this series, Analysis of Real-World Traffic Data in Germany and combining them with the idealized baseline headlight distribution from part one, different optimized headlight distributions can be generated. These headlight distributions can be optimized for different driving requirements based on the data that is used and weighting the different road types differently. The resulting headlight distribution is then compared to a standard light distribution in terms of the required luminous flux, angular distribution, and overall shape. Nonetheless, it is the overall approach that has been taken that we see as the primary novel outcome of this investigation, even more than the actual distribution resulting from this effort. Full article

A new type of grouting material—FCM (fast cementing material)—is being used in coastal and offshore infrastructure projects, such as harbor and tunnel rehabilitation. In order to investigate how this material performs under different conditions, the compressive strength, failure mode, and surface microscopic changes of different fracture penetration degrees and different crack angles of grout-reinforced specimens formed by the FCM and sandstone were investigated in an acidic environment with pH = 1.1 and after freeze–thaw cycles of 5, 10, 20, and 30 times. In addition, through the preliminary determination of FCM grouting material fluidity and setting time, it was determined that the water-material ratio in this test is 0.3, and the sandstone used has good uniformity. The results show that the strength of the original rock can be matched or even exceeded by the solid grout of FCM and sandstone. Acidic environments and freeze–thaw cycles will erode the specimens, mainly on the surface of the specimens. The fracture penetration degree and crack angle determine the degree of strength reduction of the specimens. The compressive strength of the specimens decreases most rapidly within 10 freeze–thaw cycles. After soaking in acidic solution and a freeze–thaw cycle in an acidic environment, particle shedding occurs on the surface of the grout material and a “honeycomb” area appears on the surface of the sandstone. As the freeze–thaw cycle increases, the particle-shedding area and the honeycomb area increase continuously. Full article

This study aims to identify the most effective input parameters for performance modelling of container-based web systems. We introduce a method using queueing Petri nets to model web system performance for containerized structures, leveraging prior measurement data for resource demand estimation. This approach eliminates intrusive interventions in the production system. Our research evaluates the accuracy of various formal estimation methods, pinpointing the most suitable for container environments. With the use of a stock exchange web system benchmark for data collection and simulation verification, our findings reveal that the proposed method ensures precise response time parameter accuracy for such architectural configurations. Full article

The future development of Industry 4.0 places paramount importance on human-centered/-centric factors in the production, design, and management of logistic systems, which has led to the emergence of Industry 5.0. However, effectively integrating human-centered/-centric factors in logistics scenarios has become a challenge. A pivotal technological solution for dealing with such a challenge is to distinguish and track moving objects such as humans and goods. Therefore, an algorithm model combining YOLOv5 and DeepSORT for logistics warehouse object tracking is designed, where YOLOv5 is selected as the object-detection algorithm and DeepSORT distinguishes humans from goods and environments. The evaluation metrics from the MOT Challenge affirm the algorithm’s robustness and efficacy. Through rigorous experimental tests, the combined algorithm demonstrates rapid convergence (within 30 ms), which holds promising potential for applications in real-world logistics warehouses. Full article

Aortic aneurysms (AA) occur in 4.8% of people causing 150,000 deaths annually. While endovascular aneurysm repairs reduce surgical morbidity, device-related failures (leak/displacement) are frequent highlighting the need for test models that better represent the mural geometry and compliance changes in human AAs. We aimed to develop and characterise an ex vivo porcine aortic model of AA. The optimal duration of tissue elastase exposure to emulate AA changes in elastin microstructure and content was determined using porcine aortic rings. Elastase-induced changes were quantified morphologically, and mechanical properties assessed via ring tensile testing. Subsequent experiments tested the potential for localised elastase treatment in a 1 cm segment of porcine aorta using a specially designed 3D printed rig. The effect on pressure-diameter behaviour was investigated via inflation-extension testing. Elastase treatment produced time dependent decreases in elastin, resulting in an increased tensile modulus and circumferential length in the ring samples in the final phase of the J-shaped tissue stress-strain curves. In whole aortic segments, localised elastase-induced luminal degradation was successfully limited to a central region. The degree of elastin degradation achieved was sufficient to cause localised dilation with respect to controls under physiological pressures. Localised elastin degradation in porcine aortic segments is feasible and emulates the changes seen clinically in aortic aneurysms. Full article

(1) Background: The growing ubiquity of electromagnetic fields (EMF) due to rapid technological progress raises concerns about potential health implications. While laboratory experiments have generated inconclusive findings about adverse effects, EMFs have demonstrated efficacy in magnetotherapy. Earlier studies indicate that an EMF can trigger stress responses in organisms, the outcomes of which are dependent on the intensity of the EMF. (2) Methods: This study aims to explore the effects of extremely low-frequency EMF (50 Hz, 1 mT, or 7 mT) on metamorphosis and metabolism rates, which are indicators of stress, across different developmental stages of Tenebrio molitor, including adults, pupae, and larvae. (3) Results: Our findings reveal that exposure to EMF leads to accelerated weight loss, increased adult metabolism, and higher mortality; however, EMF exposure appears to have no impact on sugar levels or the rate and success of metamorphosis. Notably, significant changes were only observed under the influence of a strong EMF (7 mT), while the weaker EMF (1 mT) did not yield statistically significant outcomes. (4) Conclusion: The obtained results suggest that an extremely low-frequency EMF can be considered a stressor, with its effects contingent upon the specific parameters of exposure and the developmental stage of the experimental model. Full article

Wind power generation is a renewable energy source, and its power output is influenced by multiple factors such as wind speed, direction, meteorological conditions, and the characteristics of wind turbines. Therefore, accurately predicting wind power is crucial for the grid operation and maintenance management of wind power plants. This paper proposes a hybrid model to improve the accuracy of wind power prediction. Accurate wind power forecasting is critical for the safe operation of power systems. To improve the accuracy of wind power prediction, this paper proposes a hybrid model incorporating variational modal decomposition (VMD), a Sparrow Search Algorithm (SSA), and a temporal-convolutional-network-based bi-directional gated recurrent unit (TCN-BiGRU). The model first uses VMD to break down the raw power data into several modal components, and then it builds an SSA-TCN-BIGRU model for each component for prediction, and finally, it accumulates all the predicted components to obtain the wind power prediction results. The proposed short-term wind power prediction model was validated using measured data from a wind farm in China. The proposed VMD-SSA-TCN-BiGRU forecasting framework is compared with benchmark models to verify its practicability and reliability. Compared with the TCN-BiGRU, the symmetric mean absolute percentage error, the mean absolute error, and the root mean square error of the VMD-SSA-TCN-BiGRU model reduced by 34.36%, 49.14%, and 55.94%. Full article