Search Results (40,257)

This work addresses the achievement of efficient control of laser light transmission through stationary microperiodic parallel stripe textures formed in films of nematic liquid crystals (NLCs) in planar-oriented cells upon a direct-current (DC) electric field. By varying the field intensity and, thereby, the field-induced periodic modulation of the nematic director and hence the complex transmittance function corresponding to the longitudinal domain texture induced in NLC films with initial planar alignment, the intensity of a linearly polarized laser beam passed through the films can be well controlled. In 25 µm-thick films of room-temperature NLCs pentylcyanobiphenyl (5CB), this results in a low-voltage (~4 V) sharp and deep V-shaped behavior of their electro-optically controlled transmittance. Such a reversible electro-optical effect is interesting for active control of laser beam intensity and other applications. The relevant physical mechanism is analyzed and explained. Full article

This case study focuses on twelve compacted clay soil samples to understand their fundamental physical and thermal properties. For each sample, the density, thermal conductivity, thermal diffusivity, specific heat, and drying shrinkage were assessed. The identification and characterisation of the materials were also carried out by positioning them into the ternary diagram based on the percentage of sand, silt, and clay. These properties are definitive for the performance characteristics of materials used in rammed earth wall construction. The aim is to provide information for better knowledge and prediction regarding the dynamic heat flow in rammed earth walls. Experimental results show a relatively wide range of values for each property, reflecting the diverse properties of the sampled clays. The thermophysical characteristics of the 12 types of earth analysed showed correlations with reports in the literature in terms of density (1490–2150 kg/m³), porosity (23.22–39.99%), specific heat capacity (701–999 J/kgK), and thermal conductivity (0.523–1.209 W/mK), which indicates them as materials suitable for use in the construction of rammed earth walls. Using test data, a dynamic assessment of heat flow through simulated rammed earth walls was performed. For a better understanding of the results obtained, they were compared with results obtained for simulations where the building element would be made of concrete, i.e., a mineral wool core composite. Thus, heat flux at the wall surface and mass flux, respectively, during the 16 years of operation showed similar evolution for all 12 types of clay material analysed, with small variations explained by differences in thermophysical characteristics specific to each type of S1–S12 earth. In the case of walls made from clay material, there is a stabilisation in the evolution of the water content phenomenon by the 5th year of simulation. This contrasts with walls made of concrete, where the characteristic water content appears to evolve continuously over the 16-year period. Therefore, it can be said that in the case of the construction elements of existing buildings, which have already gone through a sufficient period for the maturation of the materials in their construction elements, the rammed earth wall quickly develops a moisture buffer function. In the case of simulating a mineral wool core composite wall, it cannot perform as a temperature or humidity buffer, exhibiting an enthalpy exchange with indoor air that is only 4% of that of the rammed earth walls; consequently, it does not play a significant role in regulating indoor comfort conditions. Overall, there is confirmation of the temperature and moisture buffering capabilities of rammed earth walls during both warm and cold periods of the year, which is consistent with other reports in the literature. The findings of this research provide a better insight into clay as a material for rammed earth walls for more efficient design and construction, offering potential improvements regarding indoor comfort, energy efficiency, and sustainability. The data also provides useful information in the fields of architecture and civil engineering regarding the use of clay as an eco-friendly building material. The results emphasise the importance of thoroughly understanding the thermophysical properties of clay to ensure the efficiency of rammed earth construction. Full article

The purpose of this paper was to determine the effect of anodization on the in vitro proliferation and adhesion of immortalized human keratinocytes (HaCats) and mouse bone marrow-derived mesenchymal stem cells (BM-MSCs) in Titanium Grade 23 (Ti6Al4V ELI) discs and to describe the surface topography, roughness, and composition of dental implants (body and collar) and abutments submitted to an area-specific anodization process. HaCat cells and BM-MSCs were seeded onto discs with three different surface treatments: machined, area-specific anodization for abutments, and area-specific anodization for implant collars. Cell proliferation was assessed using a resazurin-based fluorescent dye on days 1, 3, and 7, while cell adhesion was examined using scanning electron microscopy (SEM). Surface topography, roughness, and composition were evaluated for six implant bodies with an anodized rough surface, six anodized implant smooth collars, and six anodized prosthetic abutments. Both HaCats and BM-MSCs showed increased viability over time (p < 0.001) with no statistically significant differences among the different surfaces (p = 0.447 HaCats and p = 0.631 BM-MSCs). SEM analysis revealed an enhanced presence and adhesion of HaCat cells on the anodized surface for the implant collars and an increased adhesion of BM-MSCs on both the anodized and machined surface abutments. The topography characteristics of the treated implants and abutments varied depending on the specific implant region. Chemical analysis confirmed the presence of oxygen, calcium, phosphorus, and sodium on the anodized surfaces. The area-specific anodization process can be utilized to create variable topography, increase the specific surface area, and introduce oxygen, calcium, phosphorus, and sodium to dental implants and abutments. While BM-MSCs and HaCat cells showed similar adhesion and proliferation on anodized and machined surfaces, a positive interaction between anodized Ti6Al4V ELI surfaces and these two cell lines present in the peri-implant mucosa was observed. Due to the limitations of the present study, further research is necessary to confirm these findings. Full article

Among the most significant causes of concrete degradation is ESA (external sulfate attack). The majority of studies are currently conducted on samples that have been saturated and matured. Concrete structures, however, are exposed to the environment once the formwork has been removed. The purpose of this study is to determine what effects early exposure to external sulfates may have on degradation mechanisms. Microstructure, physical, and chemical behavior are monitored using a variety of experimental techniques, including NMR (²⁷Al and ²⁹Si), ICP, XRD, MIP, and SEM. Based on expansion measurements, mature Portland cement paste, unlike the early-age case, degraded rapidly due to the presence of compressed ettringite and gypsum, highlighted by SEM analysis. During ESA, sulfate ions diffuse through the cement matrix and are bound by chemical agents. Chemical analyses indicate that the chemical mechanism varies with the duration of curing. At an early age, external sulfates and aluminates are the most important reagents. For matured cases, these reagents include external sulfates, calcium derived from CH dissolution, and aluminates derived from the total dissolution of AFm. Full article

Nowadays, humanity has to face the problem of constantly increasing amounts of waste, which cause not only environmental pollution but also poses a critical danger to human health. Moreover, the growth of landfill sites involves high costs of establishment, development, and maintenance. Glass is one of the materials whose recycling ratio is still insufficient. Therefore, in the presented work, the influence of the particle size and share of waste glass on the consistency, morphology, specific surface area, water absorption, setting time, and mechanical properties of geopolymers was determined. Furthermore, for the first time, the fire resistance and final setting time of such geopolymer composites were presented in a wide range. Based on the obtained results, it was found that the geopolymer containing 20% unsorted waste glass obtained a final setting time that was 44% less than the sample not containing waste glass, 51.5 MPa of compressive strength (135.2% higher than the reference sample), and 13.5 MPa of residual compressive strength after the fire resistance test (164.7% more than the reference sample). Furthermore, it was found that the final setting time and the total pore volume closely depended on the additive’s share and particle size. In addition, the use of waste glass characterized by larger particle sizes led to higher strength and lower mass loss after exposure to high temperatures compared to the composite containing smaller ones. The results presented in this work allow not only for reducing the costs and negative impact on the environment associated with landfilling but also for developing a simple, low-cost method of producing a modern geopolymer composite with beneficial properties for the construction industry. Full article

Transmission electron microscopy (TEM) is an excellent characterization method to analyze the size, morphology, crystalline state, and microstructure of perovskite quantum dots (PeQDs). Nevertheless, the electron beam of TEM as an illumination source provides high energy, which causes morphological variation (fusion and melting) and recession of the crystalline structure in low radiolysis tolerance specimens. Hence, a novel and facile strategy is proposed: electron beam peel [PbBr₆]⁴⁻ octahedron defects from the surface of QDs to optimize the crystal structure. TEM and high-angle annular dark-field scanning TEM (HAADF) tests indicate that the [PbBr₆]⁴⁻ octahedron would be peeled from the surface of QDs when QDs samples were irradiated under high-power irradiation, and then a clear image would be obtained. To avoid interference from a protective film of “carbon deposits” on the surface of the sample when using high resolution TEM, amorphous carbon film (15–20 nm) was deposited on the surface of QDs film and then characterized by TEM and HAADF. The detection consequences showed that the defection of PbBr₂ on the surface of QDs will gradually disappear with the extension of radiation time, which further verifies the conjecture. Full article

In this study, an Al–Mn–Zr alloy was designed and its microstructure and corrosion behavior compared after laser welding to that of AA3003. As the results of immersion and electrochemical tests showed, both alloys had a faster corrosion rate in the fusion zone than in the base metal. Laser welding caused interdendritic segregation, and spread the intermetallic compounds (IMCs) evenly throughout in the fusion zone. This increased the micro-galvanic corrosion sites and destabilized the passive film, thus increasing the corrosion rate of the fusion zone. However, Zr in the Al–Mn alloy reduced the size and number of IMCs, and minimized the micro-galvanic corrosion effect. Consequently, Al–Mn–Zr alloy has higher corrosion resistance than AA3003 even after laser welding. Full article

Wireless power transfer (WPT) is a technology that enables energy transmission without physical contact, utilizing magnetic and electric fields as soft media. While WPT has numerous applications, the increasing power transfer distance often results in a decrease in transmission efficiency, as well as the urgent need for addressing safety concerns. Metamaterials offer a promising way for improving efficiency and reducing the flux density in WPT systems. This paper provides an overview of the current status and technical challenges of metamaterial-based WPT systems. The basic principles of magnetic coupling resonant wireless power transfer (MCR-WPT) are presented, followed by a detailed description of the metamaterial design theory and its application in WPT. The paper then reviews the metamaterial-based wireless energy transmission system from three perspectives: transmission efficiency, misalignment tolerance, and electromagnetic shielding. Finally, the paper summarizes the development trends and technical challenges of metamaterial-based WPT systems. Full article

Lu₃Al₅O₁₂:Ce³⁺ phosphor ceramics were fabricated by vacuum sintering. On this basis, a bi-layer composite phosphor was prepared by low-temperature sintering to cover the phosphor ceramics with a layer of SrAlSiN₃:Eu²⁺-phosphor-in-glass (PiG). The optical, thermal, and colorimetric properties of LuAG:Ce³⁺ phosphor ceramics, SrAlSiN₃:Eu²⁺ phosphors and SrAlSiN₃:Eu²⁺-PiG were studied individually. Combining the bi-layer composite phosphors with the blue LED chip, it is found that the spectrum can be adjusted by varying the doping concentration of SrAlSiN₃:Eu²⁺-PiG and the thickness of Lu₃Al₅O₁₂:Ce³⁺ phosphor ceramics. The maximal color rendering index value of the white LED is 86, and the R9 is 61. Under the excitation of a laser diode, the maximum phosphor conversion efficacy of the bi-layer composite phosphors is 120 lm/W, the R_a is 83, and the correlated color temperature is 4534 K. These results show that the bi-layer composite phosphor ceramic is a candidate material to achieve high color rendering index for high brightness lighting. Full article

Pathological tooth wear is an escalating social problem. Occlusal veneers can be an alternative to traditional prosthetic restorations such as crowns, inlays, and onlays. Background: The aim of this study is to assess the fracture resistance of occlusal veneers made of various materials depending on their thickness. Methods: In total, 120 occlusal veneers were examined. The restorations were made of four ceramics: leucite LC (IPS Empress Esthetic), hybrid HC (Vita Enamic), lithium disilicate LDC (IPS e.max Press), and zirconium oxide ZOC (Ceramill Zolid HT). A total of 30 veneers were made of each material, 10 for each of the three thicknesses: 1 mm, 1.5 mm, 2 mm. The restorations were cemented on identical abutments duplicated from the developed phantom tooth 35 (KaVo) with composite cement (All Bond Universal). The samples prepared in this way were subjected to a compressive strength test in a universal testing machine. Statistical analysis of the results was performed. Results: The average fracture resistance of occlusal veneers made of zirconium oxide ceramic was 1086–1640 N, of lithium disilicate ceramics 456–1044 N, of hybrid ceramics 449–576 N, and of leucite ceramics 257–499 N. Conclusions: Occlusal veneers made of ceramics, zirconium oxide and lithium disilicate, had the highest resistance to fractures. Restorations made of leucite ceramics turned out to be the least resistant to forces. The greater the thickness of the ceramic occlusal veneers, the greater their fracture resistance. Full article

A theoretical approach based on Periodic Boundary Conditions (PBC) and a Linear Combination of Atomic Orbitals (LCAO) in the framework of the density functional theory (DFT) is used to investigate the molecular mechanism that rules the piezoelectric behavior of poly(vinylidene fluoride) (PVDF) polymer in the crystalline β-phase. We present several computational tests highlighting the peculiar electrostatic potential energy landscape the polymer chains feel when they change their orientation by a rigid rotation in the lattice cell. We demonstrate that a rotation of the permanent dipole through chain rotation has a rather low energy cost and leads to a lattice relaxation. This justifies the macroscopic strain observed when the material is subjected to an electric field. Moreover, we investigate the effect on the molecular geometry of the expansion of the lattice parameters in the (a, b) plane, proving that the rotation of the dipole can take place spontaneously under mechanical deformation. By band deconvolution of the IR and Raman spectra of a PVDF film with a high content of β-phase, we provide the experimental phonon wavenumbers and relative band intensities, which we compare against the predictions from DFT calculations. This analysis shows the reliability of the LCAO approach, as implemented in the CRYSTAL software, for calculating the vibrational spectra. Finally, we investigate how the IR/Raman spectra evolve as a function of inter-chain distance, moving towards the isolated chain limit and to the limit of a single crystal slab. The results show the relevance of the inter-molecular interactions on the vibrational dynamics and on the electro-optical features ruling the intensity pattern of the vibrational spectra. Full article

The grain size of a metallic coating or the surface layer after the machining of metallic parts strongly impacts corrosion and wear properties along with fatigue behavior. By measuring the combined electrical resistance of this layer and the substrate using the four-point probe method, the grain size of the layer can be determined. For different grain shapes, models are derived based on an analytical approach. The parameters in the models can be determined by appropriate calibration measurements. As a result, the grain sizes can be determined quickly with a non-destructive method, which can be applied to ensure consistent coating or machining results as part of quality control routines in industrial processes. Full article

To minimize the adverse effects of high temperatures on the service performance of track structures, research on the application of reflective coatings on track structures is urgently needed. Based on meteorological data and the characteristics of the multi-layer structure of the ballastless track, refined finite element models (FEMs) for the temperature field and temperature effect analysis of the CRTS III slab ballastless track structure on bridges were established. The temperature deformation characteristics and temperature stress distribution of the CRTS III slab ballastless track under natural environmental conditions were investigated. Similarly, the influence of a reflective coating on the structural temperature field and temperature effect was studied. The results showed that the temperature and vertical temperature gradient of the track slab were significantly reduced after the application of the reflective coating. Meanwhile, the thermal deformation and thermal stresses of the track slab and the self-compacting concrete (SCC) layer were minimized. Under high-temperature conditions in summer, the maximum temperature of the track slab decreased from 47.0 °C to 39.6 °C after the application of the reflective coating, and the maximum vertical temperature gradient of the track slab decreased from 61.5 °C/m to 39.1 °C/m after the application of the reflective coating. Under the maximum positive temperature gradient, the peak displacement of the upper arch in the middle of the slab and the peak displacement of the sinking in the slab corner decreased from 0.814 mm and 1.240 mm to 0.441 mm and 0.511 mm, respectively, and the maximum transverse tensile stresses of the track slab reduced from 2.7 MPa to 1.5 MPa as well. In addition, the reflective coating could also inhibit the failure of the interlayer interface effectively. The results of this study can provide a theoretical basis and reference for the application of reflective coatings on ballastless tracks on bridges. Full article

Nitrogen-doped activated carbons with controlled micro- and mesoporosity were obtained from wood and wastes via chemical processing using pre-treatment (pyrolysis at 500 °C and hydrothermally carbonization at 250 °C) and evaluated as oxygen reduction catalysts for further application in fuel cells. The elemental and chemical composition, structure and porosity, and types of nitrogen bonds of obtained catalyst materials were studied. The catalytic activity was evaluated in an alkaline medium using the rotating disk electrode method. It was shown that an increase in the volume of mesopores in the porous structure of a carbon catalyst promotes the diffusion of reagents and the reactions proceed more efficiently. The competitiveness of the obtained carbon materials compared to Pt/C for the reaction of catalytic oxygen reduction is shown. Full article

This study aimed to address the issue of high-temperature challenges in asphalt pavement by developing two types of phase change materials (PCMs) for temperature control. Encapsulated paraffin wax particles (EPWP) and encapsulated myristic acid particles (EMAP) were synthesized using acid-etched ceramsite (AECS) as the carrier, paraffin wax (PW) or myristic acid (MA) as the core material, and a combination of epoxy resin and cement as the encapsulation material. The investigation encompassed leakage tests on PCMs; rutting plate rolling forming tests; SEM, FTIR, XRD, and TG-DSC microscopic tests; as well as heat storage and release tests and temperature control assessments using a light heating device. The study revealed the following key findings. Both types of PCMs exhibited no PCM leakage even under high temperatures and demonstrated low crushing ratios during rut-forming tests. Microscopic evaluations confirmed the chemical stability and phase compatibility of the constituents within the two types of PCMs. Notably, the phase change enthalpies of EPWP and EMAP were relatively high, measuring 133.31 J/g and 138.52 J/g, respectively. The utilization of AECS as the carrier for PCMs led to a substantial 4.61-fold increase in the adsorption rate. Moreover, the PCMs showcased minimal mass loss at 180 °C, rendering them suitable for asphalt pavement applications. The heat storage and release experiments further underscored the PCMs’ capacity to regulate ambient temperatures through heat absorption and release. When subjected to light heating, the maximum temperatures of the two types of phase change Marshall specimens were notably lower by 6.6 °C and 4.8 °C, respectively, compared to standard Marshall specimens. Based on comprehensive testing, EPWP displayed enhanced adaptability and demonstrated substantial potential for practical implementation in asphalt pavements. Full article