Search Results (8,600)

From December 2021 to May 2022, MeteoSwiss and Meteomatics conducted a proof of concept to demonstrate the capability of automatic drones to provide data of sufficient quality and reliability on a routine operational basis. Over 6 months, Meteodrones MM-670 were operated automatically eight times per night at Payerne, Switzerland. In total, 864 meteorological profiles were measured and compared to co-located standard measurements, including radiosoundings and remote sensing instruments. To our knowledge, this is the first time that Meteodrone’s atmospheric profiles have been evaluated in such an extensive campaign. The paper highlights two case studies that showcase the performance and challenges of measuring temperature, humidity, and wind with a Meteodrone. It also focuses on the overall quality of the drone measurements. Throughout the campaign, the availability of Meteodrone measurements was 75.7%, with 82.2% of the flights reaching the nominal altitude of 2000 m above sea level. The quality of the measurements was assessed against the WMO’s (World Meteorological Organization) requirements. The temperature measurements gathered by the Meteodrone met the “breakthrough” target, while the humidity and wind profiles met the “threshold” target for high-resolution numerical weather prediction. The temperature measurement quality was comparable to that of a microwave radiometer, and the humidity quality was similar to that obtained from a Raman LiDAR. However, the wind measurements gathered by a Doppler LiDAR were more accurate than the estimation provided by the Meteodrone. This campaign marks a significant step towards the operational use of automatic drones for meteorological applications. Full article

This study analyzed the main features (onset, demise, and length) of the South American Monsoon System (SAMS) projected in different time slices (2020–2039, 2040–2059, 2060–2079, and 2080–2099) and climate scenarios (SSP2–4.5 and SSP5–8.5). Eight global climate models (GCMs) from the Coupled Model Intercomparison Project Phase 6 (CMIP6) that perform well in representing South America’s historical climate (1995–2014) were initially selected. Thus, the bias correction–statistical downscaling (BCSD) technique, using quantile delta mapping (QDM), was applied in each model to obtain higher-resolution projections than their original grid. The horizontal resolution adopted was 0.5° of latitude × longitude, the same as the Climate Prediction Center precipitation analysis used as a reference dataset in BCSD. The QDM technique improved the monsoon onset west of 60° W and the simulated demise and length in southwestern Amazonia. Raw and BCSD ensembles project an onset delay of approximately three pentads compared to the historical period over almost all regions and a demise delay of two pentads northward 20° S. Additionally, the BCSD ensemble projects a reduced length with statistical significance in most South Atlantic Convergence Zone regions and a delay of three pentads in the demise over the Brazilian Amazon from the second half of the 21st century. Full article

The measurement of cloud microphysical parameters plays an important role in describing characteristics of liquid phase clouds and investigating mutual relationships between clouds and precipitation. In this paper, cloud microphysical parameters at Liupan Mountain Weather Station in Ningxia are measured with a high-resolution coaxial digital holographic imager and a fog monitor 120. There are differences in the measurement results between the two instruments. The number concentration measured by the digital holographic imager is about 1.5 times that of the fog monitor 120. However, their Pearson correlation coefficient is above 0.9. Through analysis, we found that the measurement results of the digital holographic imager and fog monitor 120 are differences in 2–4 µm and 7–50µm. For the droplets with the diameters of 4–7 µm, their measurement results have good consistency. By analyzing the influence of wind field and detection sensitivity on the measurement principle, the reasons which caused the difference are proposed. Advice is given to observe topographic clouds by using the above two instruments. In addition, the differences in liquid water content and visibility are analyzed due to the absence of small and large droplets. The study provides data support for improving the accuracy of instruments in measuring cloud droplets and is useful for research in the field of cloud microphysical processes. Full article

This paper studies the three-dimensional (3-D) ionospheric electron density variation over the continental US and adjacent regions during the August 2017 Great American Solar Eclipse event, using Millstone Hill incoherent scatter radar observations, ionosonde data, the Swarm satellite measurements, and a new TEC-based ionospheric data assimilation system (TIDAS). The TIDAS data assimilation system can reconstruct a 3-D electron density distribution over continental US and adjacent regions, with a spatial–temporal resolution of 1${}^{\circ }$× 1${}^{\circ }$ in latitude and longitude, 20 km in altitude, and 5 min in universal time. The combination of multi-instrumental observations and the high-resolution TIDAS data assimilation products can well represent the dynamic 3-D ionospheric electron density response to the solar eclipse, providing important altitude information and fine-scale details. Results show that the eclipse-induced ionospheric electron density depletion can exceed 50% around the F2-layer peak height between 200 and 300 km. The recovery of electron density following the maximum depletion exhibits an altitude-dependent feature, with lower altitudes exhibiting a faster recovery than the F2 peak region and above. The recovery feature was also characterized by a post-eclipse electron density enhancement of 15–30%, which is particularly prominent in the topside ionosphere at altitudes above 300 km. Full article

Black carbon (BC), an important component of atmospheric aerosol, plays a significant role in regional climate, hydrological cycle, variation of monsoon rainfall, and human health. The 40-year detailed atmospheric BC over China from 1981 to 2020 is systematically investigated through the MERRA-2 reanalysis dataset. MERRA-2 BC generally showed a good correlation (R = 0.68) compared with 673 monthly samples from ground-based observation at 35 stations around China. The overall annual average of MERRA-2 BC concentration over China is 1.15 μg/m³, with a fast growth rate during 1981–2007 and a relatively slow decrease after that. The winter season has the highest mean concentration of BC, followed by autumn and spring, whereas summer shows relatively weaker values. The order of annual average BC concentrations during 1981–2020 is Beijing-Tianjin-Hebei region (BTH, 4.02 μg/m³) > Sichuan Basin (SB, 3.94 μg/m³) > Yangtze River Delta (YRD, 2.68 μg/m³) > Pearl River Delta (PRD, 1.47 μg/m³). The monthly mean BC concentrations over the BTH, YRD, PRD and SB are estimated to be smallest 3.18 μg/m³ in May, 1.94 μg/m³ in August, 0.82 μg/m³ in July, 3.04 μg/m³ in June, respectively, whilst largest consistently in December with 5.09 μg/m³, 3.83 μg/m³, 2.12 μg/m³, and 5.41 μg/m³, respectively. Our study indicates the primary potential source areas for BC are concentrated in the research city and its surroundings. Beijing and Chengdu are more BC-polluted areas than Shanghai and Guangzhou. Long-distance, regional transfer from south BTH contributes importantly to BC pollution in Beijing under the influence of prevailing southerly winds. The geographical location of Chengdu causes the transport and accumulation of BC inside the SB. Full article

We investigate the differences between the effects of geomagnetic storms due to Interplanetary Coronal Mass Ejections (ICME) and due to Stream Interaction Regions or Corotating Interaction Regions (SIR/CIR) on the ionospheric F2-layer during the maximum of solar cycle 24. We have created a unique list of the ICME- and SIR/CIR-driven geomagnetic storm events for the time interval between November 2012 and October 2014. Finally, 42 clear ICME and 34 clear SIR/CIR events were selected for this analysis. The individual geomagnetic storm periods were grouped by seasons, time of day, and local time of Dst_min and were analyzed using three different methods: linear correlation analysis using 4-hour averages of foF2 parameters and the geomagnetic indices (1st), daily variation of deltafoF2 (2nd), and 3D plotting: geomagnetic indices vs. time vs. deltafoF2 (3rd). The main phase day of the ICME- and SIR/CIR-induced geomagnetic storms was our main focus. We used manually evaluated ionospheric foF2 parameters measured at the Sopron ionosonde station and the geomagnetic indices (Kp, Dst, and AE) for this analysis. We have found that in most cases, the variation of the Dst index is the best indicator of the impact caused in the F2 layer. We conclude as well that the representation of the data by the third method gives a better description of the ICME and SIR/CIR-triggered storm behavior. In addition, our investigation shows that the SIR/CIR-related perturbations can be predicted with greater accuracy with the second method. Full article

Frequent heavy snowfall in Xinjiang plays an important role in the land water cycle. In this study, 18 groups of simulation experiments are conducted on the heavy snowfall event in Xinjiang during 9–13 December of 2015 using the Weather Research and Forecasting (WRF) model. In these experiments, the combination of six land surface parameterization schemes (the Noah scheme, Noah-MP scheme, RUC scheme, CLM4 scheme, PX scheme, and TD scheme) with three microphysical parameterization schemes (the WSM6 scheme, Thompson scheme, and Lin scheme) are adopted, where the observed snowfall data are used for performance evaluation. Results show that the simulated snowfall intensity and snowfall range in different areas are very sensitive to the selection of the land surface scheme. The snowfall in southern Xinjiang is overestimated by almost all six schemes, where the Noah-MP scheme performs more reasonably than the others. The Noah scheme shows its advantage in northwestern Xinjiang. The three different microphysical schemes vary significantly in producing snowfall amount. The WSM6 scheme produced the largest snowfall amount, and the Lin scheme resulted in the smallest snowfall amount. In addition, the accumulated snowfall amounts above 10 mm are generally underestimated by all six land surface schemes, while the accumulated snowfall amounts below 10 mm are overestimated by most of the schemes. The Noah-MP scheme performs the best in the simulation of the snowfall amount in the whole region. However, the Noah scheme shows an advantage in areas with a large snowfall amount. Full article

Many issues pioneered by Jackson Herring deal with how nonlinear interactions shape atmospheric dynamics. In this context, we analyze new direct numerical simulations of rotating stratified flows with a large-scale forcing, which is either random or quasi-geostrophic (QG). Runs were performed at a moderate Reynolds number $Re$ and up to 1646 turn-over times in one case. We found intermittent fluctuations of the vertical velocity w and temperature $\theta$ in a narrow domain of parameters as for decaying flows. Preliminary results indicate that parabolic relations between normalized third- and fourth-order moments of the buoyancy flux $\propto ⟨w\theta ⟩$ and of the energy dissipation emerge in this domain, including for passive and active scalars, with or without rotation. These are reminiscent of (but not identical to) previous findings for other variables and systems such as oceanic and atmospheric flows, climate re-analysis data, fusion plasmas, the Solar Wind, or galaxies. For QG forcing, sharp scaling transitions take place once the Ozmidov length scale ${\ell }_{Oz}$ is resolved—${\ell }_{Oz}$ being the scale after which a turbulent Kolmogorov energy spectrum likely recovers at high $Re$. Full article

Theoretical predictions of laser beam interactions with jet-engine-exhaust-induced turbulence are of importance for optimization of various optical systems, including LIDARs and airborne laser measurement systems. This paper is based on the extended Huygens–Fresnel diffraction integral and the Wigner distribution function, combined with the recently proposed power spectral density function of atmospheric turbulence induced by jet engine exhaust, to derive the formula for the quality factor of a partially coherent Airy beam in turbulent media induced by jet engine exhaust. Numerical calculations based on the analytical formula show that the smaller the structure constant and outer scale of the atmospheric turbulence induced by jet engine exhaust, the smaller the quality factor of a partially coherent Airy beam, indicating better laser beam quality. At the same time, the larger the generalized parameter and inner scale of the jet-engine-exhaust-induced turbulence and the longer the wavelength of the laser beam, the smaller the corresponding quality factor. The numerical results also show that reducing the coherence length of a partially coherent Airy beam and increasing its characteristic width are beneficial for reducing the quality factor in the atmospheric turbulence induced by jet engines. However, the numerical results show that increasing the coherence length of a partially coherent Airy beam and reducing its characteristic width are beneficial for reducing the quality factor in vacuum. This situation demonstrates significant differences between the interaction mechanisms of an Airy beam in vacuum and in the jet-engine-exhaust-induced turbulence. The results of our discussion contribute to clarifying the mechanism of interaction between an Airy laser beam and random media, as well as the application of a curved Airy laser beam in practical situations. Full article

The physical mechanisms associated with heat waves (HWs) are well known in the midlatitudes but still under-documented in the Sahel. Specifically, the role of anthropogenic and natural changes in tropospheric aerosols regarding HWs remains an issue to address. Our study focuses on the characterisation of the dusty HWs in the Sahel, which generally occur from March to June. The goal is to reinforce or invalidate the assumption proposed in previous studies recently carried out in southern Europe and according to which mineral dust may locally change irradiance at the surface, thus atmospheric temperatures at 2 m, intensifying the HW. The work is carried out in three steps: (i) detect and describe the HW over the 2003–2014 period based on maximum daily 2-m temperatures (T${}_{max}$) from ERA-Interim reanalyses; (ii) characterise the dust optical properties during the HW using the Deep Blue aerosols products from MODIS (Moderate Resolution Imaging Spectroradiometre): the Aerosol Optical Depth at 550 nm (AOD${}_{550}$), the Angstrom Exponent (AE${}_{440-870}$) and the Single Scattering Albedo at 412 nm (SSA${}_{412}$) as a proxy of quantity over atmospheric column, size and absorption of aerosols, respectively; (iii) relate HW intensity to the aerosol conditions during the HW. Over the 12-year study period, 14 HWs are detected when T${}_{max}$ exceeds the 90th percentile (P90). The HWs are dusty with AOD${}_{550}$ ranging between 0.46 and 1.17 and all the dust types are absorbent with a SSA${}_{412}$ value of 0.93 (round to hundredths). The HW classification according to aerosol conditions gave three HWs: Type 1 corresponds to Pure Dust Situation (PDS with AE${}_{440-870}$ = 0.1), Type 2 and Type 3 are associated with Mixed Situation (MS) with dominance of Coarse Particles (CP with AE${}_{440-870}$ = 0.35) and Fine Particles (FP with AE${}_{440-870}$ = 0.65), respectively. The main result obtained is that the intensity of the dusty HW, computed as the difference between daily T${}_{max}$ and its P90 (T${}_{max}$−P90)), is higher for Type 1 HW (+1.1 °C) in the case of the most absorbent aerosol situation (SSA${}_{412}$ = 0.931). A non-significant difference between Type 2 and Type 3 especially for temperature (+0.5 °C and +0.4 °C, respectively) and SSA (0.938 and 0.935, respectively) is observed and, during these mixing situations, the HWs are less intense than those during the PDS. Finally, the analysis of two huge Type 1 HWs in 2007 and 2010 shows that dust mass concentrations at the surface were particularly high, up to 214 μg/m³ on average. These findings enable us to assess that highly absorbent and concentrated pure dust situations observed in spring in the Sahel may have a potential warming effect at the surface. Full article

The aim of this study is to investigate the characteristics of the intraseasonal oscillation (ISO) with a 10–30-day cycle over mid-high-latitude Eurasia during boreal summer. The leading mode of this ISO is determined using an extended empirical orthogonal function analysis. Through a phase composite analysis, it is observed that a southeastward-propagating wave train with a quasi-barotropic structure is present in Eurasia. The dynamical mechanism and energy conversion affecting its propagation are also analyzed. The negative (positive) temperature tendency appears in the southeastern part of the temperature anomaly in the lower troposphere (upper troposphere), resulting in further southeastward displacement of the temperature perturbation. A diagnosis of temperature tendency shows that the main cause of the southeastward movement is the advection of anomalous temperature by the mean zonal wind. The energy conversion analysis reveals that by converting kinetic energy and potential energy, the ISO perturbation acquires energy from the summertime mean flow during its southeastward movement. Full article

Coastal areas have become the primary location for nuclear power plant sites due to the convenience of seawater cooling. In China, the diffusion range of thermal discharge water has always been a hot research topic as the basis for sea use areas. The main physical process of heat loss in the numerical simulation of thermal discharge from power plants is heat exchange between the water surface and air. Currently, the methods for calculating this heat loss include the heat flux method and the water surface heat exchange coefficient method. Taking a power plant in Zhejiang as the research object, the MIKE 3 temperature–salinity module (heat flux method) and MIKE ECO Model (water surface heat exchange coefficient method) were used for modeling, and the diffusion of thermal discharge water under different modules was compared and analyzed. The results show that the calculated area of the water temperature rise envelope between the two modules differed significantly under the same conditions. The surface 4 °C temperature rise area, as calculated using ECO Model, was 45.8% smaller than that of the temperature–salinity module. The MIKE 3 temperature–salinity module can simulate the heat accumulation of water under thermal buoyancy, producing a significant thermal stratification phenomenon; the ECO module does not accurately represent the heat exchange process between the water surface and the air, and it does not adequately capture the significant vertical stratification that occurs in real-world scenarios. On this basis, this study not only lays a foundation for further exploring the impact of thermal discharge water from this powerhouse on the structure of surrounding marine biological communities and dissolved oxygen content in water bodies but also provides scientific evidence for the selection of modules when simulating thermal discharge water with the MIKE model. Full article

Global climate change presents a significant threat to food security. Analyzing the effects of elevated ozone (O₃) concentration on photosynthetic fluorescence characteristics and yield addresses the damage of climate change on crops, which would serve food security. With open-top chambers (OTCs) and Tiefeng-29 soybeans, we investigated the responses of chlorophyll concentration, fluorescence characteristics, net photosynthetic rate (Pn) and yield components to different O₃ concentrations, which included CK (ambient concentration approximately 45 nL·L⁻¹, T1 (80 ± 10) nL·L⁻¹ and T2 (120 ± 10) nL·L⁻¹ O₃. The parent soybeans (S1) were planted in the current year, and O₃ fumigation commenced 20 days after seedling emergence. Aeration was stopped at maturity, and the offspring soybeans (S2) were retained after harvest for further experiments. In the following year, S1 and S2 soybeans were planted, and O₃ fumigation began 20 days after seedling emergence. The results show that leaf chlorophyll a (chla) and chlorophyll b (chlb) significantly decreased with longer O₃ fumigation time both in parents and offspring, causing damage to the light-trapping ability while the offspring suffered an earlier decrease. The elevated O₃ damaged the electron transfer process by significantly reducing the original and actual photochemical efficiencies of PSII both in parents and offspring. The electron transfer rate (ETR) of the parents and offspring decreased, while the difference between them was not significant after O₃ treatment. The non-photochemical quenching coefficient (NPQ) showed an increasing trend along time but showed no significant difference between parents and offspring. An elevated concentration of O₃ significantly reduced Pn, while the differences in Pn between the parents and the offspring were not significant. Elevated O₃ resulted in reduced yields in both parent and offspring soybeans. Although it was found that the offspring soybeans exhibited higher yields than the parents, their reduction in yield was more significant. Therefore, elevated O₃ concentration reduced soybean yield through damaging photosynthetic process and electron transfer capacity by impairing energy conversion and material accumulation capacity. The offspring had relatively higher light energy conversion efficiency than the parents, resulting in a higher yield than the parents under all treatments. Full article

Nitrogen dioxide (NO₂) is one of the major air pollutants in cities across mid-eastern China. Comprehending the spatial and temporal dynamics of NO₂ drivers in various urban areas is imperative for tailoring effective air control strategies. Using data from ground-based monitoring stations, we investigated the impact of socioeconomic and meteorological factors on NO₂ concentrations in cities in mid-eastern China from 2015 to 2021 using the Geographically and Temporally Weighted Regression (GTWR) model. The findings reveal a notable reduction of over 10% in NO₂ concentrations since 2015 in most cities, notably a 50.5% decrease in Bozhou. However, certain areas within Anhui and Jiangsu have experienced an increase in NO₂ concentrations. Significant spatial heterogeneity is observed in the relationship between NO₂ concentrations and influencing factors. The permanent population density (POP) and the electricity consumption (EC) of the entire society exhibited the strongest correlations with NO₂ concentrations, with average coefficients of 0.431 and 0.520, respectively. Furthermore, other economic factors such as urbanization rate (UR), the share of secondary sector output in total GDP (IS), and the coverage rate of urban green areas (CG) were predominantly positively correlated, while GDP per capita (PGDP) and civil car vehicles (CV) demonstrated primarily negative correlations. Furthermore, we examined the correlations between four meteorological factors (temperature, relative humidity, wind speed, and precipitation) and NO₂ concentrations. All these factors exhibited negative correlations with NO₂ concentrations. Among them, temperature exhibited the strongest negative correlation, with a coefficient of −0.411. This research may contribute valuable insights and guidance for developing air emission reduction policies in various cities in mid-eastern China. Full article

The fallow agricultural soils of Northwest Russia represent an evolutionary model of the development of ecosystem components in time and space with multidirectional dynamics of agrogenic impact during the long history of agricultural land development. There has been both large-scale land development and uncontrolled conversion of arable lands to a fallow state along with their removal in recent times. All this has led to the formation of a chrono-series of different-age soils with varying degrees of exposure of agrogenic factors. This paper presents a current review of the humus state of fallow soils in Northwest Russia, and examines the main factors (self-restoration, humus transformation, acidification) influencing the transformation of the soil cover under the process of post-agrogenesis. Effective farming techniques aimed at fixing carbon in soils as part of increasing the sequestration potential to mitigate the impact of climate change are considered. The ongoing process of the transition of lands into a fallow state could lead to organic carbon losses and changes in the main physical and chemical parameters, which negatively affects the self-restoration of fallow lands. We offer some recommendations for the effective rewetting of fallow lands in Northwest Russia with the purpose of carbon sequestration in the soil cover. Full article